THE POWER BEHIND THE TECHNOLOGY

As more and more systems move toward using IP-based devices connected to the local building data network, the owner has to determine how those IP-based devices will obtain the DC power required for them to operate. To make sure all of us are on the same page; I am specifically referring to Wireless Access Points, Voice Over IP (VoIP) phones and IP security cameras. Door access control units and their related locking mechanisms operate on DC power, but the wide variety of current draw requirements, dependent upon the locking device, may require placing them on a separate power source.

You have three choices regarding DC power for IP devices. You can use a data switch or patchbay with POE (Power Over Ethernet) built in, an AC-to-DC power supply located in a wiring closet or an AC-to-DC hardwired transformer located in an electrical box near the device. Some solutions are superior to others so let’s review all three options.

Sorry about getting geeky, but we need to. IEEE (Institute of Electrical and Electronic Engineers) is the international organization that issues consensus-based standards for the electrical and data/cabling industries.“IEEE-802.3af” is the standard for distribution of DC voltage across data switches, patch bays and UTP Cat5e/6 cabling to power IP devices and is called POE (Power Over Ethernet). I personally think using POE on a data switch is an extremely limiting way to distribute DC power, because Gigabit Ethernet and POE are inherently incompatible with each other. You cannot use POE with a copper-based Gigabit Ethernet circuit. Copper-based data connections are DC voltage based binary systems, meaning there is DC voltage on the cable with one level of voltage representing“0” and a higher voltage representing “1.” Fast Ethernet (Base100T) runs at 100Mbps and uses two of the four pairs of a UTP cable. Gigabit Ethernet (Base1000T) runs at 1000Mbps and uses all four pairs of a UTP cable. Guess what? The POE standard uses the fourth pair for distributing a constant DC voltage to the IP device.

Wait a minute! If I have a constant DC voltage going down the UTP cable’s fourth pair, how can I see the DC voltage differences for my “0s” and “1s”? You can’t! Oooopppsss!

When I think about the life-cycle of phones and cameras in a school, versus data switches, I can see some real problems for schools down the road. Due to manufacturing cost reductions, five years from now your computers will come with Gigabit Ethernet built in and you will be required to upgrade your data switches. But when you do that, your new switches will not have POE capability and your Wireless Access Points, VoIP phones and IP cameras will not work.

Installing a POE (IEEE-802.3af) patchbay in the wiring closet is a better solution, but you should also know that there are manufacturers with individual POE inserters for locations with few IP devices connected to a wiring closet. For all POE solutions, you will need to calculate the actual maximum current draw for all IP devices to ensure the load is within the capability of the device.

A second, but more expensive, alternative is to install a security industry, rack-mounted 18-24VDC power supply in the wiring closet and a one pair 18awg cable, which is daisy chained to each IP device. A third and most expensive solution requires locating an electrical junction box near the IP device and installing a hardwired AC/DC transformer in the box. However, locating power for Wireless Access Points cannot occur ahead of the RF site survey, which establishes the optimum location for those devices.

About the Author

Glenn Meeks is president of Meeks Educational Technology located in Cary, N.C. He can be reached at [email protected].

Featured

  • Springfield Breaks Ground on $53.7M Pipkin Middle School Rebuild

    Construction is underway on a new, state-of-the-art Pipkin Middle School in Springfield, Mo., a major step in Springfield Public Schools’ (SPS) long-term facility improvement plan, according to local news. The $53.7-million project officially broke ground in early June, following years of planning and community input aimed at modernizing aging infrastructure and addressing student capacity concerns.

  • ProTeam Launches GoFit 6 HEPA Backpack Vacuum

    Technology leader Emerson recently introduced the new ProTeam GoFit 6 HEPA backpack vacuum, according to a news release. The vacuum was designed to capture 99.97% of particulates down to 0.3 microns—including atmospheric hazards like lead dust, mold spores, and other particulates—through an advanced filtration system.

  • California High School Starts Construction on New CTE Building

    Analy High School, part of the West Sonoma County Union High School District (WSCUHSD) in Sebastopol, Calif., recently broke ground on a new Career Technical Education (CTE) Building, according to a news release. The 15,000-square-foot facility will offer specialized facilities for students in engineering, welding, culinary arts, agricultural sciences, and design thinking.

  • modern college building with circuit and brain motifs

    Anthropic Introduces Claude for Education

    Anthropic has launched a version of its Claude AI assistant tailored for higher education institutions. Claude for Education "gives academic institutions secure, reliable AI access for their entire community," the company said, to enable colleges and universities to develop and implement AI-enabled approaches across teaching, learning, and administration.

Digital Edition